![]() It will always be greater than the poll interval. The actual cycle period is dependent on the serial communications baud rate, the size of the commands, and the responsiveness of the transceiver. The rigCAT code operates in a separate thread during which the various queries are made with a default interval of 100 milliseconds between the last query and the start of the next cycle. Used for correct startup of K9MJ CI-V router Xcvr/interface echoes all chars (typical of CI-V interface) Use command string for PTT (not supported by all xcvrs) Set DTR signal line to + 12 V (default -12 V) Set RTS signal line to +12 V (default -12 V) Wait time after sending init string to xcvr Wait time after sending normal command to xcvr On a subsequent start of fldigi the saved parameters will override the ones in the rig definition file. If a value is changed on the configuration tab it is saved in the progdefaults.xml file if the configuration is saved. These values are loaded from the xml file. The serial port parameters may be preset in the xml file and also set or changed on the rigCAT configuration tab. The title bar tag pair contains the text which will be displayed on the window decoration bar, as in: Rig Control - IC-746 PRO Is not used by the parser, but should as a minimum state whether the definition file has been "Verified", is "Alpha&", what the Version and Date of creation or update, as in: Verified Version: 1.0 Date: 2007 Jan 5 The text within the tag pair is not used by the parser, but should as a minimum say who created and who tested the definition file, as in: The text within the tag pair specifies the transceiver to which this file applies, as in: Icom 746 PRO You are encouraged to study the various rig definition files to learn more about how they are organized.Ĭomments are contained within the tag pair: Īnd may appear anywhere in the rig definition file The entire rig definition must be contained within the tag pair If you create, test and verify the proper operation for a transceiver not yet posted please share that with others by sending it as an attachment to feedback w1hkj com and I will post it on the web site. You will find subdirectories by manufacturer which contain files named by rig type, ie: TS-850.xml. These are found in the xmls directory on this site: xml archives. Very impressed with these current programs.This document describes the contents of the rig definition file "rig.xml".Ī number of transceivers have rig definition files written and tested which you may use. I have never used SOUND card modes before, I always used HARDWARE. ![]() The 991 RF gain I use to control the waterfall blue yellow issues. This is where I set CW, RTTY, and packet modes.Īs you change these modes the lower LEFT corner will reflect the change. It worked for me.ĭATA-USB is set under the freq readout on FLDIGI I keep it set to that for everything.įLDIGI SCREEN under the freq readout there is a option: OP MODE. If you save this frequency to a memory, the DATA-USB Mode and the function selections will all be saved.ĭisclaimer: it was on original write up. ( turn off the MONI if you wish.) I like it on. This should show a blue background on the FLDIGI waterfall from about 200 to 3000 HZ. ( this will also be used in receive mode for fine adjustments.) The MULT knob until the width reads 3000HZ. Now move the options buttons until you find the WIDTH button. Shift the options buttons until you find NAR/WIDE button. Adjusting the RF GAIN will be used a lot during receive. ( you may use the DT gain for fine level corrections during operation. Then select the ALC meter and press the DT GAIN button and adjust the MULTI KNOB for no ALC indication. Using the Windows Mixer for Playback Device, turn down the USB AUDIO CODEC playback slider to show 50 watts on the 991 power meter. ON FLDIGI, Push the tune button (upper right hand corner of window). Hit the 991 F button, shift through function option and set MONI to on. Turn up the 991 RF gain control, then use the WINDOWS mixer record control the USB AUDIO CODEC to turn down the waterfall shows mostly blue with some yellow noise spots. Should be in DATA-USB or it will not transmit. Set the 991 mode to DATA-USB using either the FLDIGI RIG MODE select box or ![]() Se lect OP Mode at top of FLDIGI screen to RTTY.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |